The Furuno LS is the little brother to the LS with a slightly smaller screen size, but with all of the power and features to satisfy both entry level and more. Furuno LS Fishfinder is a high contrast monochrome fishfinder with a large screen designed for small craft. Furuno LS has 5 display pages including. The Furuno LS is a dual frequency fish finder designed for small pleasure craft. It features a waterproof 5” high-definition silver bright LCD.

Author: Fenrigrel Mushicage
Country: Central African Republic
Language: English (Spanish)
Genre: Technology
Published (Last): 22 December 2013
Pages: 108
PDF File Size: 8.99 Mb
ePub File Size: 2.11 Mb
ISBN: 906-8-49430-741-5
Downloads: 94470
Price: Free* [*Free Regsitration Required]
Uploader: Tataur

Page 8 Note 1: There are no uer-serviceable partsinside. Transom Mount Transducer Construction of fairing block 3. Don’t see a manual you are looking for? Page 13 Adjusting the gainftftftftft60ft30ft15ftThe [GAIN] key adjusts the sensitivity ofthe receiver.

Or point us to the URL where the manual is located. Thewater temperature, arrival and speedalarms require appropriate sensors. A special connectoris required to test the NMEA port.

Furuno LS Fishfinder, no transducers Price

Troubleshooting table If… Then check … neither echo nor battery voltage. Nothing appears if no connector isconnected.

Repeat step 1 to ensure that theangle of the sensor is correct. Contact yourdealer for connection ofother equipment.

  AGIP 7007 0W30 PDF

Turn the battery voltage indication appears at the top right corner on the screen on or off. Your manual failed to upload Carefully remove anymarine life with a piece of wood orfine-grade sandpaper.

What’s missing? Tell us about it.

Position thecover over the cable where it entersthe hull. LowAuto mode options window4. Table of Contents Add to my manuals Add. Page 17 MENU from page 2 on the menu. Operation Selects basic display range. Fill the gap between the wedge frontof the transducer and transom withepoxy material to eliminate any airspaces. Sandpaper Silicone sealant Silicone grease Remarks on installation If you cannot restorenormal operation, contact your dealerfor advice.

Adjust the brilliance asnecessary.

FURUNO LS4100 Fishfinder

Mount the sensor close to the centerlineof the boat. Repeat step 1 to ensure that the angle of the sensor is correct. When the bottom depthincreases, the display shift to keep thebottom echo at the lower part of thescreen. Page 25 Requires appropriate nav data.

A warning label is attached to the equipment. This may require a certain amount of experimentation for fine tuning at high cruising speeds. When choosing alocation keep the following in mind: If a hole has been drilled 41100 the transom, open the appropriate slot in the transom cable cover. Mounting locationTo ensure the best performance, thesensor must be submerged inaeration-free and turbulence-free water.


5″ LCD SOUNDER LS | Fish Finder | Products | FURUNO

Position the second cable clamphalfway between the first clamp andthe cable hole. Sediment in the water or reflectionsfrom plankton may be painted on thedisplay in low intensity tones. Depth, temperature, speed setting window Choose On to output input data. Single frequency display 50 kHz The sounder uses ultrasonic signals to detect bottom conditions. Enter text from picture: During the developmental phase the reliability and availability of the WAAS signal cannot be guaranteed.

Mount the sensor close to the centerline of the boat. The start upscreen appears with the maximumbrilliance. Appearance of weak echoes These weak echoes may be erased as follows: Page 13 Basic ranges default 3. The waypoint list appears,with the erased waypoint blank. Leave slack in cables to facilitate checking and maintenance.

It is useful forestimating the kind of fish school andbottom composition. The squares at the right side of thetest display are for checking thecontrols.