FLUKE MICROSCANNER2 MANUAL PDF

get started using the tester. For additional information, see the MicroScanner2 Cable Verifier. Users Manual on the Fluke Networks website. Safety. Warning. MicroScanner2 Cable Verifier. Accessing the Users Manual. This guide provides basic information to help you get started using the tester. For additional. View and Download Fluke MicroScanner 2 user manual online. Cable Verifier. MicroScanner 2 Test Equipment pdf manual download.

Author: Doulkree Gashicage
Country: Gambia
Language: English (Spanish)
Genre: Finance
Published (Last): 11 February 2014
Pages: 474
PDF File Size: 6.21 Mb
ePub File Size: 8.46 Mb
ISBN: 487-7-54806-317-9
Downloads: 99662
Price: Free* [*Free Regsitration Required]
Uploader: Vill

Do not put in sunlight. The display shows a scrolling sinewave in analog toner mode 2.

LCD display with backlight. The higher the number, the stronger the signal. Use the tester to check for shorts. Fluke Networks does not warrant that software will be error free or operate without interruption. Results Screens for Individual Wire Pairs Using the Toner in IntelliTone Mode. Fault Locators and Tone Generators. Detects the advertised speed of Table of Contents Add to my manuals Add.

This crossed pair is likely caused by mixing A and B cabling. Press PORT to select manaul pair cabling. Do not use this function on powered wires. Copper Cable Testers and Tone Generators. Category 8 Cable Testing.

MicroScanner2 Getting Started Guide, Rev. 1 | Fluke Networks

Use the probe to isolate the tone source in the cable bundle or at the patch panel. MicroScanner Cable Verifier Users Manual split pair, 15 telephone voltages, 16 —U— universal adapter, 10 —V— version information, 41 voltage detection, 5, 16 —W— wiremap adapter, Specifications Specifications Specifications Specifications apply at 23 C 73 Funless otherwise noted. Page 33 – Connecting to a Telephone Network Wired Page of 60 Go. Note Use the SmartTone function only on dry pairs of wires that are unterminated at both ends.

  CUMMINS JETSCAN 4062 MANUAL PDF

Clean the display with glass cleaner and a soft, lint-free cloth.

LEDs show the wiremap. IntelliTone mode is indicated by IntelliTone and a scrolling pattern of 1s and 0s on the display. Page 2 Fluke Networks warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Integrity Networks Alaska Branch. The display shows the song number 3.

Don’t show me this message again. The pin numbers flash to indicate the fault.

Telephone cables wired micrkscanner2 a star topology Figure 16 are connected together at a bridge tap at the distribution If you connect the tester to the bridge tap, the tester center. Adrian Young Creation Date: Detection of crossed pairs requires a far-end adapter. The analog toner has four songs. Index testing —R— coaxial cabling, 28 registration, 1 twisted pair cabling, 11 remote ID locator, 10, 22 toner, 32 replacement parts, 42 analog mode, 35 RJ11 jack, 10 IntelliTone mode, 32 SmartTone function, 35, 36 —S— troubleshooting safety information, 3, 39 cabling faults, 47 serial number, 41 the tester, Split Pair Wires connected to wrong pins at connector or punchdown Open block.

The the pin wires flash to indicate the fault.

If the song changes when you release the short, you have found the cable connected to the tester. The rightmost segments indicate the shield. Don’t have an account? See explanations in the manual. Dashes are shown if the tester cannot Ethernet Port Detected measure the length. This equipment is intended for Fluke Networks. In a split pair, continuity from end to end mqnual correct, but is made with wires from different pairs.

  CAKKAVATTI SIHANADA SUTTA PDF

Toning in IntelliTone™ Mode – MicroScanner2

SmartTone works with the IntelliTone probe and with analog probes. The digital IntelliTone signal is easier to detect at a distance than analog tones, and its frequency and encoding eliminate cable misidentification due to signal bleed and radiated or ambient noise. For the latest list of options and accessories visit the Fluke Networks website at www.

Length is not shown because the voltage interferes with length measurements. The distance to a bridge tap is approximate because multiple reflections from the bridge tap interfere with length measurements. MicroScanner Cable Verifier Users Manual Regulatory Information This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the manual, may cause interference to radio communications. Momentarily short a wire pair in a cable twisted pair or short the conductor and shield in a cable coaxial.

Locations of the tester and wiremap adapter may be swapped. Fiber Inspection and Cleaning.