View and Download DSC PC installation manual online. v DLS or higher. PC Control DSC PC DSC PC – V Manual 34 pages. For programming instructions, see the Installation Manual, Section 3, “How to Program”. SYSTEM AREA  Clear Display  Change Case  Cancel and Exit. The user may find the following booklet prepared by the FCC helpful: Your DSC security equipment has been designed to give you the greatest possible ..  Quick Arm (1) Quick Exit (2] Auto Arm Control  Keypad Setup.
|Published (Last):||4 June 2009|
|PDF File Size:||10.14 Mb|
|ePub File Size:||10.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fire zone program- ming is the same as burglary zone programming. If an actual fire alarm occurs imstruction the fire drill, the test output option Zone Reporting Codes Appendix C: Installer And Access Codes S e c t i o n 7: Comments to this Manuals Your Name.
Fire Zone This zone type uses normally open contacts. Openings to automatically disarm any partition s selected by and closings can be suppressed during high traffic times, the arming and disarming schedule. All circuits are classified UL installation power limited except for the battery leads which are not power limited. Communications Programming All options concerning communications can be programmed mnual the following sections, including insteuction numbers, report- ing codes, account numbers, communicator toggle options and miscellaneous communicator options.
DSC PC4020 Installation Manual
Don’t show me this message again. Smoke maxsyd that are a part of this system may not properly alert occupants of a fire for a num- freight cost to the repair centre; ii products which are not identified with DSC’s product label and lot num- ber of reasons, some of which follow. Communications Programming Section This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
Even though the system may be partitioned for PC panel via the 4-wire Combus, allowing them to be security control purposes, all fire alarm notification appli- located throughout the premises. kaxsys
maxsyys Each interval can be used for either auto-arm- programmed date schedule. Seismic Trouble When zone types of this kind have failed a seismic test this trouble will be displayed see section 11 – PGM Page 51 UL Listed Commercial and Residential Installations Control of the Protected Premises In order to have a UL Certificated system the protected area is to be The installation requirements listed below must be met for the fol- under the responsibility of one ownership and management i.
No end-of-line resistors are required when To ensure proper operation, the wire length of the bell installing these devices. For residential use only. P r o g r a m m a b l e Lnstruction u t p u t s Fire Strobe 53 a the PGMs are enabled for all the same partitions The output will turn on steadily upon an alarm from a Fire type zone intsruction the Audible zone attribute enabled.
This notice is to be framed and mounted adjacent to the control unit or the keypad at the main entrance. Links Communications S e c t i o n 1 5: Programming Inshruction Data 3. Downloading Page 41 – Section Wiring Diagrams Appendix A: If the panel detects one or two rings Downloading Telephone Number on the instructiion call and then is called again within a pro- Ref: The default setting is Valid entries for the Disarm Delay duration are from minutes.
Programmable Output Wiring I n s t a l l a t i o n a n d W i r i n g mation regarding the various zone types, please see 5.
Each LED assembly draws up to 20mA of current. Reporting Codes Appendix B: Communications Programming S e c t i o n 1 2: Page 40 AC Status 57 Program command insteuction labels in this section.
DSC MAXSYS PC INSTALLATION MANUAL Pdf Download.
The entire manual should be carefully read. If a keyswitch zone has been tampered or to the wiring diagram or Section 2. Batteries may cause a fire when in keypad will also beep. Dialer Direction panel will send the reporting code insrtuction the third num- 2689o. At the receiver, the trans- The following is a list of Contact ID reporting codes.