EN , Adhesives – Terms and definitions. ASTM B, Standard Test Methods for Measuring Resistance of Electrical Connections (Static. ASTM Standards: 2. B Test Methods for Measuring Resistance of Electrical 1 This guide is under the jurisdiction of ASTM Committee B02 on Nonferrous. Astm B 02 Pdf Download ->->->-> 3cbf. AdlerRelated InterestsGrammatical GenderGenderEthnicity, Race.
|Published (Last):||18 February 2012|
|PDF File Size:||13.43 Mb|
|ePub File Size:||19.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence.
Enter your personal account email address to request a password reset: The resulting electrical contact resistance is shown by the first set of conditions in FIG. Click here to download full list of books. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
There were no books found for the applied search filters. When present, the latter of these is usually much greater aetm value and dominates the contact resistance. Test Criteria The criteria for evaluating the contact resistance of electrical connections largely depends on the type of connection e. Copyright Compu-tecture, Inc.
The criteria employed in evaluating contact resistance and stability are not a part of these test methods as they depend on specific applications and xstm, will not be quantitatively stated. Please login to your authorized staff account to use this feature. Resistances measured by these methods before, during and after simulated life tests are used as a means of determining the stability of contacts within a asttm.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Historical Version s – view previous versions of standard.
These will differ by equipment and manufacturer and there is no code or standard that mandates minimum contact resistances. The latter case was discussed in Electric Contacts by Holm. As real contact surfaces asrm varying degrees of roughness, real contacts are necessarily composed of many contact spots which are electrically parallel. In addition, acceptably low values atm contact resistance astm b 02 often obtained with true areas of contact being significantly less than the apparent contact area.
Both of these atsm should be considered when evaluating contact systems. The term metallic contact as used here is intended to include the so called quasi-metallic contact spots as well. Search book title Enter keywords for book title search. Nails, Spikes, and Staples. F Standard Specification for Driven Fasteners: No items in cart. On the one hand, the absolute value of contact resistance is greatly dependent on the amount of metallic contact established and indicates initially how efficient the system is in producing areas of metallic contact.
In one astmm, the composite product is post-treated below or above the melt temperature of the tin-containing particles in a controlled vacuum or gas atmosphere.
Package Engineer shall follow thru with Buyer from Procurement Dept to ensure astm b 02 additional scope is covered in the PO. This is the result of having a large number of small contact spots spread out over a relatively large apparent contact area. From here we can detect and rectify any miss alignment earlier prior delivery. For a given contact spot, when the film resistance is zero or negligible the contact resistance for that spot is nearly the same as the constriction resistance and therefore, as a practical matter, has a minimum value which represents a clean metal-to-metal contact spot.
The latter case was discussed in Electric Contacts by Holm. Print 1 2 3 4 5 page sstarting from page current page. The following editions for this book are also available Under a fourth set of conditions b39-02 include exposing the composite product to mixed flowing gas for example, MFG class IIa for 2 days at conditions which metallic copper generally corrodes and shows degradation in the contact resistance responses, the electrical contact resistance is between 4 and 5 milliohm, after a wiping of at least micrometers.
Contact Resistance (Ductor) Test | iSTiQAMAH
Enter your personal account email address to request a password reset: Resistances measured by these methods before, during and after simulated life tests are used as a means of determining the stability of contacts within a device.
The criteria employed in evaluating contact resistance and stability are not a part of these test methods as they depend b539-002 specific applications and therefore, will not be quantitatively stated. However, an estimate of contact resistance 3 resulting from good metallic contact can be made for a given physical situation and used as a comparison to actual measurements to determine how effective the system is in establishing astj metallic contact. Fill in your details below or click an icon to log in: The test measures the resistance at the micro- or milli-ohm level and is used primarily to verify that electrical connections are made properly, and can detect the following problems: The criteria employed in evaluating contact resistance and stability are not a part of these test methods as they depend on specific applications and therefore, will not be quantitatively stated.
Link to Active This link will always route to the current Asym version of the standard. Customer shall insist for Bus Bar to be fully connected using bolting as per actual condition at site.
The contact resistance test commonly known as the Ductor test measures the resistance of electrical connections such as joints, terminations, connectors, etc. You are commenting using your Twitter account. B Standard Specification for Refined Lead.
ASTM B539 02 EPUB DOWNLOAD
Remember me for one month. Both of these characteristics should v539-02 considered when evaluating contact systems. However, an estimate of contact resistance 3 resulting from good metallic contact can be astm b 02 for a given physical situation and used as a comparison to actual measurements to determine how effective the system is in astm b 02 stable metallic contact.