MANUAL AUTORIZACION BTP PDF

Edinson Borda Villcas. Test de Percepcion Visual Frostig Manual. Uploaded by. MARIA Abs Cambios Uploaded by. Patricio Patri. Manual Autorizacion Btp. Manual Autorizacion Btp. Uploaded by. Patricio Patri · PROBMON1-Ser Omni 6- 25 Min (Problemas). Uploaded by. Patricio Patri · Test Psi Co Tec Nico. Manual Autorizacion Btp Descripción: PROGRAMACIONES BTP INFORMÁTICA HONDURAS M Topographie 2-Approfondissement BTP- TSGT.

Author: Mukora JoJogar
Country: Peru
Language: English (Spanish)
Genre: Software
Published (Last): 4 June 2018
Pages: 481
PDF File Size: 15.9 Mb
ePub File Size: 2.39 Mb
ISBN: 580-3-21754-398-6
Downloads: 40544
Price: Free* [*Free Regsitration Required]
Uploader: Bami

It is also necessary for inspecting the clamping function of disc springs. This will engage the pinion onto the gear teeth of the nut Now place springs 11 and lock-nut 12 in position. B – El Sistema Turret o Radial. If the clearance is more, it should be adjusted by replacing the flange 25 by a new flange of suitable extra thickness.

Denel Turret Lct30 Full description. Your consent to our cookies if you continue to use this website. However, care should be taken while mounting the encoder back in its position. Control should be capable of detecting the proximity switch signal within 3 to 6 ms. Relatively small value components. Temps Unitaire en btp Documents. If plate is not available you may use tool disc in place of the plate.

Manual Autorizacion Btp – Editorial Tráfico Vial – Google Books

Assembly Reference Quantity Drg. Valve button continuously presses against coolant flange 26 fitted on indexing flange. Insert allen key in bolt head socket and tap it with hammer. Cam follower roller Track roller Track roller pins 42 78 77 Spindle assembly Indexing drive Indexing drive 3 8 8 Remaining components of the cam shaft are to be assembled bgp a later stage. Machine surface should be either scraped or surface-ground. Procedure for setting the encoder in proper angular orientation is as follows: Coolant flow automatically stops during the indexing movement, as the coolant flange closes the opening of the valve button.

  CATALOGO DE PRODUCTOS VIAKON PDF

Such a condition is usually associated with the change in angular position of tool disc in the clamped position or excessive noise in one direction during indexing. Bolts htp be tightened in gradual manner, in 3 to 4 stages. Circular parts of cam 75 should contact the rollers Bring the Indexing flange along with tool disc, if it is not removed in proper angular position.

Screws 30 and 44 should be tightened firmly after coating them with anti vibration solution like Locktite. Adjustment of rotary encoder. Bolt holes in the tool disc should be of extra large size to allow for angular adjustment.

Tighten locknut by hand, so that it will press the springs with a light pressure.

Rent E Books Manual Autorización Btp Epub | Website for downloading cbse books!

A drain plug has been provided to drain out the oil, if so required. Hand cranking is bttp for inspecting the setting of encoder and proximity switch. Now use a ring spanner to rotate pinion shaft, and to tighten the nut till it butts against shaft shoulder.

It might therefore be necessary to employ high pressure coolant pump, to ensure sufficient flow at tool point.

It is necessary to select particularly fast PLC programmable logic controller for the control of turret operations. Crank the motor by hand in both directions, and check for the correct indexing movement. If in two pieces, ensure that the assembly confirms to the side view shown in the figure. Vigilance in Transport Operations. Copyright by SNBC.

  EUROCAE ED-23C PDF

Rent E Books Manual Autorización Btp Epub 8488815417

Drum Cam Sub-assembly Fig Stage Lp Btp bon. For replacement, loosen the clamp and move the coolant ring to bring the valve in a suitable position to get access to the plug Refer main assembly drawing fig.

Then gently fit the encoder in position ensuring that slot fits properly on the pin. Coolant ring should then be shifted back and clamped in original position. Hexagon head of motor shaft is now approachable. Following measures are suggested for stopping the motor in minimu m possible time.

Indexing cam 75 may be in a single piece, or in two pieces depending on method of manufacture. Turret is lubricated by medium viscosity gear box oil.

It is preferable to allow the turret to slip in the event of an accidental shock or overload. Donnees de Bases Btp. Tool indexing cycle on manual demand: Fit the partial spindle assembly into the main body 45 with the help of bolts 2 and cyl.

Autorizaciln tap the bolt heads 15 using allen key to release the Ringfeder clamp. Unused electrical entry points to be properly plugged.

Solid state relays should be incorporated in the motor circuit to ensure fastest possible disconnection. Clamping bolts should use machine washers of extra thickness min. This is the maximum time manula for completing the indexing operation.

Assembly of turret requires careful attention to detail.