ASTM B Standard Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement. ASTM B Standard Guide for Post-Coating Treatments of Steel for Reducing_ 化学_自然科学_专业资料。后电镀产品处理,降低氢脆的风险标准. Buy ASTM B R GUIDE FOR POST-COATING TREATMENTS STEEL FOR REDUCING THE RISK OF HYDROGEN.
|Published (Last):||21 January 2012|
|PDF File Size:||17.44 Mb|
|ePub File Size:||18.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
Link to Active This link will always route to the current Active version of the standard. Current edition approved April 1, Some companies consider the high temperature bake as sufficient to replace the hydrogen embrittlement relief if it can be done within 4 hours, but you would need to check with your customer first before going down that route.
If you feel that your comments have not received a fair hearing you should make your views known b85 the ASTM Committee on Standards, at the address shown below.
NOTE 2—The treatment class selected is based on experience with the part, or similar parts, and the speci?
ASTM B Class 3 post heat treatment vs. ASTM B embrittlement relief
Last previous edition approved in b580 B — This heat treatment procedure shall be used after plating operations but prior to any secondary conversion coating operation. I’m an engineer trying to write good drawing notes for plating requirements. Originally approved in The heat treatment does not guarantee complete freedom b50 the adverse effects of hydrogen degradation.
A number in parentheses indicates the year of last reapproval. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The coating changes from an amorphous structure to a crystalline structure and no longer exhibits self-healing properties. I figure that if I ask a plater to plate a part per a specification, the least I can do is read the specification and give them all of the ordering information they need to plate our parts per the specification.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. It’s not possible to diagnose a finishing problem or the hazards of an operation via these pages. It is recommended that the tensile strength be supplied by the purchaser.
It is the responsibility of the user of this standard atm establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. No further reproductions authorized. B — 98 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
ASTM B850 – 98(2015)
No other units of measurement are included in this standard. This heat-treatment procedure shall be used after plating operations but prior to any secondary conversion coating operation. Referenced Documents purchase separately The documents listed below are referenced within ast, subject standard but are not provided as part of the standard.
So, generally it is hydrogen embrittlement relief bake first and heat treatment second. This heat-treatment procedure shall be used after plating operations but prior to any secondary conversion coating operation. Heat Treatment After Processing 6. NOTE 1—The heat treatment does not guarantee complete freedom from the adverse effects of hydrogen degradation.
Thanks for your help. Historical Version s – view previous versions of standard. For cadmium, tin, zinc, their alloys, or any other coating receiving astj chromate treatment, heat treatment shall be conducted before chromate treatment. Except for surface-hardened and shot-peened parts, the choice of embrittlement-relief heat treatment and the corresponding treatment conditions shall be selected on the basis of actual tensile strength of the steel.
February 24, — apologies, finishing. Class ER-0 treatment is therefore provided for parts that the purchaser wishes to exempt from treatment. This abstract is a brief summary of the referenced standard.
NOTE 5—The time period referred to is the length of time between the end of the plating operation and loading of the item concerned into the heat treatment processor.
Hi Richard, If the high temperature treatment cannot be done within a reasonable time at least within 4 hours of plating then the embrittlement relief bake needs to be done first. NOTE 3—The use of inhibitors in acid pickling baths may not minimize hydrogen embrittlement. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
A superscript epsilon e indicates an editorial change since the last revision or reapproval. Preparation involving cathodic treatments in alkaline or acid solutions shall be avoided. From beautiful Asttm Beach New Jersey: Guide ASTM B is a better document to use as a guide to the minimum times for de-embrittlement operations, especially true when you get up the the high tensile strength or very hard materials. Embrittlement Relief Treatment Classes 5.
Hi Richard, Bit of an odd one this. This phenomenon often occurs in alloys that show no signi?